Resolver Based Clutch Brake Controls

PressCommander 
Exceeds OSHA 1910.217 & ANSI B11.1-2009, “Control Reliable Design,” with dual logic power supplies, heavy duty resolver and cable, System diagnostics and programming in plain English/Spanish which can control up to four sets of operator stations (2 operators standard), Major faults such as E-Stop, motion, brake monitor, and sensor faults are handled by two force-guided relays (Form B safety relays), Off–inch–single–continuous, Continuous ARM; top stop, anti-tie down and anti-repeat, SPM Range (1 to 500), Password and supervisory controlled keyed selector switch for security of data entry, Interrupted stroke provision with indicator, Inch mode monitoring, Crank angle and speed readout (SPM), Time-based brake monitor, Built-in motion detector and drift fault, 90° and 270° stop time tester/meter built-in, Built-in hour meter for maintenance, Built-in variable speed compensation, Servo-feed interface built-in, Six optically isolated die protection inputs, Six PLS (programmable limit switch) output relays, 100 job memory, Stroke, batch, quality, and part counters, Batch counter output relay, Die protection output relay, Speed output relay, Auxiliary output relay, Optional Ethernet or DeviceNet and PC Link to allow offline job creation and storage. (For Custom Programming & Remote Field Upgrades, please consult factory at service@pressroomelectronics.com or (630) 443-9320.) Optional 10.1” color touchscreen replaces the standard display shown. Touchscreen is shown to the left and includes Production Monitoring. PressCommander >>

PressCommander Touchscreen PressCommander Touchscreen >>

PCS-05 | PCS-08

The Board Only PressCommander Module (Part #PCS-05).The redundant clutch/brake punch press control module with a remote panel mount message display (available in English or Spanish).

The PCS-08 includes the same options as the PCS-05, but also includes the IEC switches, push buttons and legend plates.

Both models comply with section 1910.217 of the Federal Register and ANSI Standard B11.1-2009. PCS-05 >>   PCS-08 >> 

PCS-10
The compact Model PCS-10 is big in safety and automation control. The redundant clutch/brake punch press control module has a remote panel mount message display (available in English or Spanish). Complies with section 1910.217 of the Federal Register and ANSI Standard B11.1-2009. PCS-10 >> 

PCS-20
Encompasses all of the features and components of Model PCS-10 plus all of the switches, legend plates, push buttons, and indicator lights for easy mounting into your existing control. Complies with section 1910.217 of the Federal Register and ANSI Standard B11.1-2009. PCS-20 >> 

PCS-2000
The Model PCS-2000 Control System is completely prewired and ready for installation. System supplied complete with a well marked terminal strip for easy, safe, and accurate electrical interface to the various punch press components. Due to the hybrid design characteristics, a main power disconnect switch and magnetic motor starter can be supplied in the same control panel. PCS-2000 >> 

PCS-4000
Incorporates all the requirements of OSHA for control reliability and component monitoring. Also includes component and system diagnostics with indicator lights for total press monitoring.  When foot actuation is used, a method of guarding the point of operation must be provided. Complies with section 1910.217 of the Federal Register and ANSI Standard B11.1-2009. PCS-4000 >> 

The Ultimate
The most feature intensive air clutch punch press control available. The control conforms to all current OSHA and ANSI standards for control reliability and component monitoring. System incorporates the PressCam 8 for complete punch press synchronization and flexibility for all peripheral punch press signaling needs such as feeds, die protection, lubrication, blow-offs, etc. All of the electrical timing adjustments for the complete press operation are done at the floor level by the operator. The PressCam 8 system also has a large job memory of 100. This gives the control the ability to remember 100 complete different jobs or die set-ups at the press. The memory concept at the press is an excellent feature due to the tremendous time saved during set-ups of various operations. Additional time is saved by being able to adjust or “fine tune” the stamping process while the press is running, which is an aid in maximizing press utilization. The Ultimate >>