What Is Electronic Cam? An electronic cam is a programmable motion-control method. A slave axis follows a defined position, speed, or timing relationship to a master axis. No cam lobe, no follower, no machined profile. A controller does the work in software.

The term confuses people because "cam" means several things. A mechanical cam shapes motion by physical contact. A die cam unit is a mechanical device built into a stamping die. A car's camshaft opens engine valves. An electronic cam is none of these. It is a control function.

This article covers how electronic cams work, their components, benefits and limits, how they differ from mechanical cams, and where they show up in automation and pressrooms.

Key Takeaways

  • Electronic camming ties slave axes to a master axis through a stored cam profile or table.
  • A typical system needs a master encoder, controller or drive, actuator, and feedback.
  • Digital profiles make changeovers more flexible, but setup and tuning still matter.
  • In pressrooms, weigh camming against clutch/brake controls, press timing, and safety requirements.

What Is an Electronic Cam?

An electronic cam is a programmed relationship in which the master axis position determines the slave axis position. Siemens describes its cam object as y = f(x), with master values on x and slave values on y, in its S7-1500 manual. It describes a control function, not one specific hardware part.

Master and slave axes

The master sets the reference position or cycle. The slave follows a programmed response: move, dwell, accelerate, decelerate, or return at specific points in that cycle.

Cam profiles and cam tables

The relationship is stored as a profile, curve, or table of matching master and slave positions. The controller interpolates between programmed points, typically linear or cubic.

Electronic versus physical cam

A mechanical cam creates motion through its shape and follower contact. An electronic cam recreates that relationship with sensors, software, drives, and an actuator.

Related terminology

Vendors use the words differently:

  • Rockwell: MCCP calculates a profile, MAPC executes position camming, and MATC supports time- or master-driven operation.
  • Siemens: cam technology object, leading axis, following axis.
  • Beckhoff: MC_CamIn couples master and slave through a cam table.

"Cam table," "cam controller," and "master-slave motion control" overlap, so check the platform's own documentation.

How Does an Electronic Cam Work?

System components

Tolomatic identifies three essentials: master speed/position sensing, a controller holding the programmable relationship, and an electric actuator for follower motion. The signal flow runs in four steps:

  1. The master encoder reports position.
  2. The controller looks up that position in the cam profile.
  3. It sends the matching command to the slave drive.
  4. Feedback closes the loop and corrects error.

Capturing the master position

The controller tracks master position, not just elapsed time. If line speed changes, the slave stays in step. Rockwell's MAPC works this way, while its MATC instruction is time-driven.

Programming the cam profile

Engineers define position, dwell, velocity, acceleration, and return portions of the cycle in a table. Interpolation fills the gaps between points. Smooth transitions matter because abrupt velocity or acceleration changes cause impact, vibration, noise, and wear. Siemens supports continuity conditions at profile boundaries for this reason.

Four-stage electronic cam signal flow from encoder to feedback

One Rockwell caveat: with MATC, the profile sets speed and acceleration, and configured axis maximums do not apply.

Executing synchronized motion

The controller keeps comparing the master's current position with the programmed relationship. It updates the slave command each cycle. A Rockwell flying shear shows the pattern: a conveyor-roll encoder is the master, and the shear matches speed during the cut, then retracts.

Feedback, tuning, and safe operation

Camming only coordinates well when the whole system is specified correctly.

  • Encoder resolution: maxon's guidance notes backlash and drivetrain elasticity can make load accuracy worse than motor-encoder resolution suggests.
  • Tuning: wrong loop settings and mechanical resonance cause axis problems.
  • Noise: poor grounding or shielding can produce erratic motion.
  • Safeguarding: motion control does not replace required safety functions.

Electronic Cam vs. Mechanical Cam

How a mechanical cam operates

A shaped cam on a shaft pushes a follower. Cam geometry fixes the motion, converting rotary input into linear, oscillating, or intermittent output.

How an electronic cam operates

No physical contact path exists. Sensors and software determine the slave command from the master's position.

Flexibility and changeovers

Different product sizes or strokes can mean replacing a mechanical cam. With electronic camming you load a different stored profile. Beckhoff even supports switching cam tables while coupled. Changeover time savings vary by machine and setup, so measure the difference on your own equipment.

Mechanical versus electronic cam changeover flexibility comparison

Performance and maintenance trade-offs

Factor Mechanical cam Electronic cam
Motion source Physical geometry Software profile
Strength Robust, predictable Programmable, synchronized
Wear concerns Impact and wear from abrupt motion Feedback wiring, tuning, resonance
Changeover Part swap or adjustment Profile change

Electronic systems still need electrical, sensor, actuator, and software upkeep.

When a hybrid system may be appropriate

Choose mechanical, electronic, or hybrid based on:

  • Required force, speed, and repeatability
  • Environment and changeover frequency
  • Safety architecture and available controls
  • Lifecycle cost

Siemens has documented a hybrid transfer setup in which electronic transfer motion synchronizes to a mechanical press encoder. The press stays the physical master.

Benefits, Limitations, and Selection Considerations

Benefits

  • Flexible motion profiles without swapping mechanical cams
  • Coordinated multi-axis movement from a shared master
  • Easier product changeovers with stored recipes
  • Speed-based synchronization as line rate changes
  • Multiple machine formats held in controller memory

Ask the manufacturer for documentation before relying on cycle-time, accuracy, downtime, or maintenance-savings figures. Unsupported numbers are not a basis for selection.

Limitations

  • Higher programming complexity than mechanical cams
  • Risk of encoder or feedback failure
  • Servo tuning after setup or changeover
  • Servo-drive and platform compatibility limits
  • Sensitivity to electrical noise on feedback lines
  • Need for qualified commissioning and support

Selection checklist

  1. Master-axis signal type and quality
  2. Slave force and travel
  3. Speed range
  4. Required dwell and acceleration
  5. Control-platform compatibility
  6. Safety functions
  7. Environmental conditions
  8. Serviceability

Applications of Electronic Cams in Automation and Pressrooms

Common automation applications

  • Flying shears and rotary knives cutting to length (Rockwell publishes example libraries for both)
  • Packaging, forming, filling, and sealing, such as Bucher's electronic cam-disc packaging machines
  • Synchronized feeders and material handling
  • Indexing tables and coordinated assembly

Electronic cam concepts in metal stamping

Synchronized control applies to press timing, feeders, transfer equipment, and clutch/brake sequencing. Siemens describes press feeds driven by positioning or a cam curve, with transfer motion synced to a mechanical press encoder or a servo press virtual axis. These are control applications. They differ from physical cam units built into stamping dies.

Electronic cam control applications across pressroom automation systems

One distinction matters. A programmable limit switch triggers discrete outputs at crank positions. That is position-based switching, not a slave-motion profile. Safety is separate too: OSHA 1910.217 sets requirements for clutch/brake control reliability and brake monitoring that a motion cam does not satisfy.

Pressroom Electronics and press controls

Dedicated press controls handle that clutch/brake reliability and timing layer, separate from motion-cam profiles. Pressroom Electronics makes customized pressroom controls, including resolver-based and rotary-cam-based clutch/brake controls.

Its PressCam 8 uses a brushless resolver in place of a mechanical rotary cam switch. Programmable timing outputs can control feeds, transfers, blow-offs, lubrication, die protection, and indexing. It stores 100 jobs, recalled by die number.

Manufacturers, press rebuilders, and maintenance teams evaluating punch press upgrades should note the limits: some models are for part-revolution presses only and cannot go on full-revolution presses. The right architecture depends on the press, timing needs, safety design, and automation integration.

Review your existing controls first, then consult a qualified press-control specialist before selecting or replacing components.

Frequently Asked Questions

What does a cam do in a car?

An engine camshaft uses shaped lobes to open and close intake and exhaust valves at set times as the crankshaft turns. It is a mechanical cam, not an industrial electronic cam.

What are the different types of cam mechanisms?

Common types include disc (plate), cylindrical (barrel), and translating or wedge cams, each paired with a follower. Electronic camming is a control method, not a physical cam shape.

What is electronic camming used for?

It synchronizes axes with a master motion in cutting, indexing, packaging, feeding, assembly, and coordinated press automation.

How does an electronic cam work?

A master encoder reports position. The controller reads a stored cam table and commands the slave actuator through a drive, with feedback closing the loop.

What is the difference between a mechanical cam and an electronic cam?

A mechanical cam creates motion through physical geometry and follower contact. An electronic cam produces software-defined motion through sensors, drives, and actuators.

Does an electronic cam eliminate mechanical components?

No. It replaces the cam-based motion relationship, but motors, actuators, bearings, structures, and sensors remain.