Encoders vs Resolvers Encoders and resolvers both tell a controller where a shaft is, how fast it's turning, and which way. On servo axes, CNC rotary tables, and punch presses, that signal drives motion accuracy, stopping control, and uptime.

The choice affects more than the sensor. It touches controller compatibility, environmental tolerance, retrofit effort, and maintenance. Cost matters too: Siemens reports that the world's 500 largest companies lose almost $1.4 trillion annually to unplanned downtime, about 11% of revenues. That figure isn't specific to feedback devices, but it shows why a wrong choice gets expensive.

This guide compares the two technologies and gives a practical framework for stamping applications.

Key Takeaways

  • Encoders typically output digital signals; resolvers output analog sine/cosine signals that need decoding.
  • High-resolution, digitally integrated motion favors encoders; heat, shock, vibration, and contamination favor resolvers.
  • Neither wins universally. Drive interface, environment, accuracy needs, and lifecycle cost decide.
  • Evaluate the whole feedback chain, not just the sensor.

Encoders vs Resolvers: Quick Comparison

Sensing Method and Output Signal

Encoders use optical or magnetic sensing. An optical encoder reads a light/dark pattern on a rotating code disk. A magnetic encoder detects field changes from a magnetized wheel or ring, and conditioning circuitry produces digital signals.

Output comes in two forms:

  • Incremental: counts pulses from a reference point, with A/B quadrature channels offset 90 degrees and an index pulse once per revolution
  • Absolute: reports position directly, within one revolution (single-turn) or across multiple revolutions (multi-turn)

Resolvers are electromechanical. An AC-excited rotor winding couples to two stator windings displaced 90 degrees, producing sine and cosine amplitudes that vary with shaft angle. Brushless designs use a rotary transformer, so there are no brushes or slip rings.

Accuracy, Resolution, and Dynamic Response

Resolution is the smallest measurable movement. Accuracy is how far the reported position deviates from true position. Kollmorgen notes that accuracy is generally worse than resolution, so bit counts alone mislead.

  • Dynapar HS35R encoder: 1 to 20,000 pulses per revolution (one product, not an industry range)
  • AMCI R11X-C12/5 resolver: ±5 arcminutes maximum
  • Tamagawa TS2640N321E64: ±10 arcminutes typical
  • Dynapar resolvers: ±2 arcminutes advertised

Digital encoder output generally suits fast positioning and servo work. Resolver performance depends on pole configuration and the converter behind it.

Environmental Durability

Published ratings vary by model, so compare datasheets rather than technology labels.

Device Temperature Shock Vibration Enclosure
Dynapar HS35R optical encoder -40 to +85 °C (with qualifications) 400 g, 6 ms 20 g IP67, conditional
AMCI R11X-C12/5 resolver -40 to +125 °C 50 g, 11 ms 15 g to 2,000 Hz IP40
AMCI HT-20 resolver -40 to +125 °C 50 g, 11 ms 15 g to 2,000 Hz IP67 with sealed connector

Environmental ratings comparison for encoder and resolver feedback devices

Resolvers have no sensitive electronics in the sensor, which helps with heat, shock, oil, and electrical noise. Brushless construction isn't an enclosure rating, though.

Integration and Maintenance

  • Encoders: often connect directly to digital drives; verify interface (TTL, HTL, 1 Vpp, EnDat, SSI), voltage, resolution, wiring, and software setup
  • Resolvers: need excitation and resolver-to-digital conversion
  • Converter example: Analog Devices AD2S1210 offers 10- to 16-bit resolution and needs an external buffer amplifier for excitation

Cost and Total Cost of Ownership

Neither technology is always cheaper. Sensor price is one line item. Installed cost also includes:

  • Converters, buffers, and excitation electronics
  • Cabling, since single-cable designs cut installation labor
  • Controls changes and engineering time
  • Spares, calibration, and maintenance
  • Downtime when feedback fails

The cheapest sensor can carry the highest lifecycle cost.

What Are Encoders and Resolvers?

Encoders and resolvers both report shaft position to a control system, but they work differently. Knowing how each type behaves helps you choose the right feedback device for a press control or automation retrofit.

What Is an Encoder?

A rotary encoder converts shaft position, speed, and direction into an electrical signal for a controller, drive, or monitoring system. "Encoder" covers a family of devices: incremental or absolute, optical or magnetic. Incremental units track change; absolute units report a unique position on power-up.

Encoder Use Cases

Encoders fit servo motors, CNC equipment, assembly lines, and production monitoring where precise position or digital integration matters. Shops use them for controlled motion, repeatable cycles, and feedback that supports fault detection.

Documented examples:

  • Haozhi's CNC rotary tables use RESOLUTE absolute optical encoders. A Renishaw case study reports ±10 arcsecond table accuracy.
  • SICK mounts an AFS60 absolute encoder on a press eccentric shaft to find stroke position and top and bottom dead center.
  • Pressroom Electronics' BM-1600 brake monitor uses a rotary encoder driven 1:1 by the crankshaft to measure stopping time, with ±1 millisecond system accuracy.

What Is a Resolver?

A resolver is a rotary transformer. A reference excitation goes in, sine/cosine signals come out, and the control system derives angle, position, and speed. Resolvers generally give absolute angular information within one revolution, and often need a converter or compatible controller.

Resolver Use Cases

Resolvers suit heat, shock, vibration, contamination, electrical noise, and legacy machinery. AMCI lists stamping press lines among its resolver applications. Wintriss's SmartPAC PRO takes crankshaft position from a resolver to track strokes, good parts, and die hits.

Encoder and resolver industrial application fit comparison

Before you specify either device, confirm it matches the existing control architecture and any converter or controller already on the press.

Encoders vs Resolvers: What Is Better?

It depends on the application. Evaluate these factors:

  • Controller interface
  • Required feedback performance
  • Environment
  • Mechanical fit
  • Safety requirements
  • Serviceability and total cost

When to Investigate an Encoder

  • You need high-resolution feedback or rapid dynamic response
  • Your drive expects digital input
  • Space is tight
  • The environment is reasonably controlled, or the encoder's published ratings cover it

When to Investigate a Resolver

  • Heat, vibration, shock, contamination, or interference is severe
  • The machine and controls already use resolver feedback

Pressroom Electronics' PressCam 8 resolver is passive, with no sensitive electronics. It is rated for -20 to 125 °C, 200 G shock for 11 ms, and 20 g vibration to 2,000 Hz.

Its Model E-160 encoder, used in brake monitoring, is rated 0 to 50 °C. Both suit their jobs; they're built for different ones.

Retrofit Requirements

Matching the sensor isn't enough. Verify:

  • Shaft or coupling dimensions and mounting tolerances
  • Excitation voltage and frequency (AMCI specifies 6.0 V at 1,000 Hz; Tamagawa 7 Vrms at 10 kHz)
  • Output format and drive compatibility
  • Cable routing, kept away from high-current lines
  • Feedback scaling, programming, and commissioning

Drive migrations show the stakes: Kollmorgen documents that moving from AKD to AKD2G may require different feedback options, an adapter, and new cables.

Metal-Stamping Checklist

  • Press speed and stroke rate
  • Clutch/brake configuration and brake monitoring
  • Machine age and existing control architecture
  • Guarding and safety controls
  • Heat, oil, coolant, and vibration exposure
  • Production criticality and available spares
  • Consequences of a feedback failure

OSHA 1910.217 matters here. Where operators place hands in the point of operation using specified safeguards, a control system and brake monitor meeting the control-reliability and brake-monitoring provisions are required. Shaft feedback is only one part of that safeguarding system.

Pressroom Electronics provides resolver-based and rotary-cam-based clutch/brake controls and customized punch press controls. Compatibility varies by press, so confirm fit before assuming any control is a drop-in replacement.

Real World Examples/Case Studies

Haozhi CNC Rotary Tables

Renishaw's 2020 case study describes Haozhi Mechanical and Electrical, a CNC rotary-table builder. Size and performance constraints called for absolute rotary feedback, so Haozhi chose RESOLUTE absolute optical encoders with RESA rings.

Reported results for the integrated tables (not the bare encoder):

  • ±10 arcsecond positioning accuracy
  • ±2 arcsecond repeatability

This is a precision-machining case, not stamping, and the study does not include downtime or cost figures.

The takeaway: compact, high-accuracy, digitally integrated motion favored an absolute optical encoder.

Haozhi CNC rotary table encoder accuracy and repeatability results

Resolver Retrofit Context in Stamping

Pressroom Electronics' Industrial Grade Brushless Resolver Transducer (Part No. 40-003) replaces the mechanical rotary cam switch on punch presses. It's built for harsh pressroom conditions:

  • Press shock and vibration
  • Temperature extremes
  • Oil and coolant mists

Those conditions favor resolver feedback in press controls.

Planning a punch-press control retrofit or resolver-based application? Contact Pressroom Electronics at 800-937-4334 about a customized control solution.

Conclusion

Encoders are often a strong fit for high-resolution, digitally integrated motion control. Resolvers stay valuable where ruggedness, harsh-environment tolerance, or compatibility with existing controls comes first.

The best decision comes from evaluating the whole machine and feedback chain:

  • Production needs
  • Safety controls
  • Environment
  • Maintenance resources
  • Long-term cost

Test the full safety system at the start of every shift, whichever device you use.

Frequently Asked Questions

What are encoders and resolvers, and how do they differ?

Both convert shaft motion into electrical feedback. Encoders typically output digital signals and offer high resolution; resolvers output analog sine/cosine signals and tolerate harsh conditions, but need conversion.

Do you need an encoder with a servo motor?

A servo needs position or speed feedback, but not necessarily an encoder. Resolvers and other technologies work, depending on the motor and drive.

What are the symptoms of a bad encoder?

Position errors, jitter, count errors, unexpected stops, feedback alarms, or erratic motion. Check wiring, alignment, coupling, power, and the controller before replacing the encoder.

Are resolvers more reliable than encoders?

Resolvers can tolerate extreme heat, vibration, and contamination, but no universal ranking exists. Reliability depends on the specific design, installation, and conditions.

Which is better for harsh industrial environments, an encoder or resolver?

A resolver often suits severe conditions. Heavy-duty encoders can also work when their published ratings meet the application.

Can a resolver replace an encoder?

Only if the drive, signal conversion, wiring, software, mounting, and feedback requirements are compatible. Get an engineering review first.