
But the catalog number isn't the whole story. Terms like PPR, CPR, and bits get used loosely, and resolution gets confused with accuracy all the time.
This guide defines high-resolution rotary encoders, untangles the terminology, compares encoder types, and gives you a selection framework for motors, CNC machines, robotics, and punch presses.
Key Takeaways
- High resolution means the smallest detectable increment, not guaranteed accuracy or repeatability.
- Incremental and absolute encoders differ in startup behavior and power-loss recovery.
- Mounting, environment, interface, and controller capability shape real-world performance.
- The right encoder meets the full motion requirement, not the biggest count on the data sheet.
How High-Resolution Rotary Encoders Measure Motion
What Is a High-Resolution Rotary Encoder?
A rotary encoder is a feedback device mounted to or built into a rotating shaft. It reports angular position, speed, direction, or motion changes to a controller.
"High resolution" has no shared numerical cutoff. Maxon's high-resolution encoder guide shows that a positioning task and a constant-velocity task need very different counts per turn. What counts as "high" depends on the job.
Take a press crankshaft. Finer increments let the controller see a change in motion sooner, which sharpens timing and stopping-time measurements. Pressroom Electronics' BM-1600 brake monitor works this way: its encoder is driven 1:1 by the crankshaft and reports stopping time in milliseconds.
How Is Encoder Resolution Expressed?
Vendors use several terms, and they don't always agree:
- PPR: pulses per revolution. US Digital reports PPR after resolution multiplication.
- CPR: cycles per revolution at some vendors, counts per revolution at others.
- LPR: equally spaced radial lines on the code disk.
- Bits: used by absolute encoders. An n-bit encoder gives 2^n positions per revolution, so 14 bits equals 16,384 positions.
The angular increment is 360 degrees divided by steps per revolution. At 4,096 steps, each step is about 0.088 degrees.
Native, Interpolated, and Multiplied Resolution
Three layers sit behind the number on a data sheet:
- Native resolution: the physical detail the sensor produces
- Interpolated resolution: positions calculated by internal signal processing
- Multiplied resolution: counts the controller takes from signal transitions
A quadrature example: a 1,000-cycle-per-revolution encoder, counted on both edges of A and B (4x), yields 4,000 increments per revolution. Maxon's ENX 16 RIO shows the layered effect, with 256 disk lines, interpolation up to 256, and up to 65,536 counts per turn.

Always confirm whether a data-sheet figure is stated before or after quadrature multiplication.
Resolution Versus Accuracy and Repeatability
RLS defines three related specs:
- Resolution: the smallest detected movement
- Accuracy: closeness to the true position
- Repeatability: the maximum difference between measurements at the same actual position
Fine resolution can still produce bad results. A code wheel, shaft, coupling, bearing, or mounting error pushes reported position off true. Renishaw notes that interpolating between graduations can introduce cyclic sub-divisional error.
The data sheets show the gap:
| Product | Resolution | Accuracy |
|---|---|---|
| HEIDENHAIN ECN 425 | 25 bits | ±20 arcseconds (system) |
| SICK DFS60B-S4UA04096 | 4,096 PPR | ±0.05 degree |
| RLS AksIM-2 | Up to 20 bits | ±0.004 degree (system) |
More bits didn't mean tighter accuracy in every row. Compare both numbers.
Types of High-Resolution Rotary Encoders
Classification systems overlap. Encoders can be sorted by output (incremental or absolute), sensing principle (optical, magnetic, and others), or mechanical configuration (shaft, hollow-shaft, kit). Keep the three axes separate.
Incremental Rotary Encoders
Incremental encoders generate pulses as the shaft turns. A and B channels sit 90 electrical degrees apart, which gives direction and allows 4x counting. The Z channel gives one index pulse per revolution.
They have no inherent position memory. After power loss or a controller reset, the system may need a homing routine. They suit speed control, conveyors, motor feedback, and machines that already home at startup.
Absolute Rotary Encoders
Absolute encoders assign a unique digital value to each shaft position, so the controller knows where it is at startup. Single-turn units repeat every revolution. Multi-turn units also track the turn count: the HEIDENHAIN EQN 437 gives 25-bit single-turn position plus a 4,096-revolution range.
Verify how turns are retained:
- Geared: a secondary code disk indexes as the primary completes revolutions.
- Wiegand-wire: pulses power turn counting without a backup battery.
- Battery-supported: a battery retains the count, so the battery becomes a maintenance item.
Expect more wiring and data handling than with incremental units. Most use serial interfaces such as SSI, BiSS-C, or EnDat, so plan for controller compatibility and higher cost.

Optical, Magnetic, and Other Sensing Technologies
| Technology | Strength | Limitation |
|---|---|---|
| Optical | High precision and resolution | Contamination or condensation on the code wheel distorts signals |
| Magnetic | Tolerates dirt, moisture, vibration | Nearby magnetic brakes can disturb signals |
| Capacitive | Detects capacitance changes | Still susceptible to electrical interference |
| Inductive | Tolerates contamination, vibration, magnetic fields | Rotor-to-sensor gap must be maintained |
The best technology depends on the machine environment, not resolution alone. Confirm ratings in current manufacturer documentation for your environment.
Shaft, Hollow-Shaft, and Kit Encoders
Mounting style drives installation and alignment needs:
- Solid-shaft units need a flexible coupling to the driven shaft
- Hollow-shaft and through-bore units slip over the shaft and use a flexible mount
- Kit or modular encoders are bearingless and fit tight retrofits, but need careful alignment (RLS specifies mounting tilt below 0.2° for the AksIM-2)
Collect this before selecting:
- Shaft diameter and mounting pattern
- Allowable radial and axial loads
- Maximum speed
- Enclosure requirements
How to Choose a High-Resolution Rotary Encoder
Start With the Motion Requirement
Document the smallest motion to detect, position tolerance, speed range, acceleration, reversals, and duty cycle. Then account for the drivetrain. Dynapar's encoder handbook notes that a 10-pitch lead screw moves 0.1 inch per revolution. Gearing and screw pitch change the resolution you need at the machine output.
Calculate from actual movement, not the largest catalog count.
Match Resolution to Accuracy and Repeatability
Evaluate resolution alongside accuracy, repeatability, hysteresis, jitter, and thermal drift, in units that fit the application (degrees or arcseconds). Drivetrain and mounting errors can dominate even when the encoder is excellent.
Choose Incremental or Absolute
- Pick incremental when relative motion, speed, direction, or a homing process is acceptable.
- Consider absolute when position must be known immediately after startup or power interruption.
- Decide single-turn versus multi-turn based on how many shaft revolutions the machine travels.
Verify Interface and Controller Compatibility
Check output type, voltage, frequency, cable length, shielding, connectors, and supported controller inputs. HEIDENHAIN lists TTL at typically 5 V differential RS-422, with a 100 m cable maximum under specified conditions, and HTL at 10 to 30 V.
Bandwidth matters. Dynapar's rule: maximum resolution = operating frequency × 60 ÷ maximum RPM. Too much resolution can overwhelm the encoder or the receiver.

Evaluate Mechanical and Environmental Conditions
Review enclosure rating, temperature, humidity, oil, dust, washdown, vibration, shock, and EMI. NEMA says IP codes and NEMA Types can't be exactly equated.
The SICK DFS60 lists -40 to +100 °C, IP67 housing, and 80 N radial and 40 N axial shaft loads. A lower-resolution encoder with better protection often outperforms a finer one that is poorly matched to its environment.
Plan for Validation and Support
Test under real conditions: startup, low speed, top speed, reversals, vibration, thermal change, and electrical noise.
Confirm on the data sheet before you buy:
- Resolution, accuracy, and repeatability
- Update rate and interface
- Environmental ratings and mounting dimensions
- Replacement part availability
For retrofits, custom machines, or safety-related architectures, get technical support before buying.
Industrial Applications for High-Resolution Rotary Encoders
- Servo and robot joints: position, velocity, and torque feedback; Renishaw notes reduction gears add elasticity, so joint-level sensing helps.
- CNC and indexing: A/B/C axis positioning on rotary tables and direct-drive motors.
- Conveyors and printing: speed and registration feedback.
- Inspection and metrology: wafer inspection, form measurement, goniometers.
- Punch presses: crankshaft angle for timing feed, pilot release, transfer, and lubrication, plus cam sequencing and stopping-time monitoring.
On punch presses, encoder feedback does not replace safeguarding. Under OSHA 1910.217, point-of-operation guards or devices, control reliability, and brake monitoring remain separate requirements. Wintriss also states its programmable cam must never provide safety timing.
Teams evaluating press-control upgrades should weigh how feedback needs interact with resolver-based and rotary-cam-based clutch/brake controls. Pressroom Electronics can discuss compatibility and customized control needs.
Installation and Integration Considerations
Mechanical Mounting and Alignment
- Keep the shaft concentric and use a flexible coupling
- Mount rigidly; avoid side loads that damage bearings or distort feedback
- Never force a coupling or use the encoder as a structural bearing
Follow the manufacturer's limits. The BM-1600's E-160 encoder allows 35 lb radial and 40 lb axial load. If chain bounce causes erratic stopping times, add an idler pulley to take up slack.
Electrical Installation and Signal Integrity
- Use shielded cable and keep it away from motor, starter, contactor, and solenoid wiring. Dynapar specifies at least 12 inches of separation.
- Protect the cable from crushing.
- Ground shields per the manufacturer; Dynapar and HEIDENHAIN prescribe differently.
- Respect termination guidance, such as HEIDENHAIN's load impedance of 100 ohms or more for TTL.
Noise, long cables, shorts, miswiring, and receiver-frequency limits all create apparent position errors.
Commissioning and Troubleshooting
- Confirm mechanical alignment so the shaft runs true under load.
- Verify count direction matches the control's expected rotation sense.
- Check index or home behavior against the machine reference.
- Compare commanded and reported position at several stroke points.
- Test the full speed range for dropouts or noise-related errors.
- Record baseline readings for later comparison.
Common fault patterns:
- Erratic counts or drift: loose mounting, coupling slip, chain or belt slack, or noise pickup
- BM-1600 drive-failure code: incorrect cable hookup, a faulty encoder, or a shaft that isn't turning
Frequently Asked Questions
What are the three main types of encoders?
It depends on the classification. By output: incremental and absolute. By sensing: optical, magnetic, and capacitive or inductive. By mechanical design: solid shaft, hollow shaft, and kit.
Can you give me an example of an encoder?
An incremental quadrature encoder on a motor shaft reports speed and direction. An absolute encoder on a CNC axis or robot joint reports exact angle at startup.
What is considered a high-resolution rotary encoder?
There's no universal threshold. Judge resolution alongside accuracy, repeatability, speed, and controller capability.
What is the difference between PPR, CPR, and encoder resolution?
PPR and CPR are pulses or cycles/counts per revolution; resolution is the smallest detectable step. Vendors define them differently, so confirm whether counts are before or after quadrature.
Are absolute or incremental encoders better for high-resolution applications?
Neither wins universally. Absolute gives direct position; incremental works well for relative motion, speed, and systems with homing.
How do I choose a rotary encoder for a punch press or industrial machine?
Define required resolution, timing, speed, mechanical fit, environment, and controller interface. Coordinate the choice with the complete press-control system.